----------------------------------------------------------------------------- MEKA - Technical Stuff ----------------------------------------------------------------------------- ----------------------------------------------------------------------------- SUMMARY ----------------------------------------------------------------------------- 1. Sega Master System & Game Gear quick specifications 2. SMS Joypads Pinouts 3. SMS Joypads (DB-9) to Parallel port adapter (type 1) 4. SMS Joypads (DB-9) to Parallel port adapter (type 2) 5. SMS Joypads (DB-9) to Parallel port adapter (GNU/Linux) 6. SMS 3-D Glasses to Serial/COM port adapter 7. More ? ----------------------------------------------------------------------------- ----------------------------------------------------------------------------- 1. Sega Master System & Game Gear quick specifications by Omar Cornut ----------------------------------------------------------------------------- Mainly intended for webmasters who would like to put some technical information about Sega 8-bit systems. If you want to know way more about them, check out S8-Dev at the following address: http://www.smspower.org/dev CPU: Zilog Z80 at 3.58 mhz (3.579545 hz to be exact). RAM: 64 kbits (= 8 kbytes) SaveRAM: Battery backed memory. Included on certain cartridges only. usually one or two banks of 128 kbits each (= 16 kbytes). Video RAM: 128 kbits (= 16 kbytes) Colors: 32 (16*2) on-screen, with an available palette of 64 colors on the Master System and 4096 on the Game Gear. Resolution: 256x224 pixels. In video modes used by the very most games, only the top 256x192 pixels or the top right 248x192 pixels are shown on the screen. On the Game Gear, a 160x144 pixels centered area is always shown. Characters: 8x8 pixels, using one of the two 16 colors palette. Up to 512 characters can be stored in VRAM but usually only 448 are used because there will be not enough room to store actual screen and sprite tables. Sprites: maximum of 64 sprites on-screen, 8 per lines. Sized of 8x8 or 8x16 pixels, using one of the two 16 colors palette (the same for all sprites). May be masked by foreground tiles. Scrolling: hardware scrolling, vertical and horizontal, line-based, allowing raster effects. Scrolling can hardware ignored for the top 16 pixels (used in many games for a status bar) and for the 64 rightmost pixels (used by Gauntlet and Golvellius in vertical stages). Audio: three tone channels with 1024 different frequencies and one noise (sound) channel. 16 different volume step. optional YM-2413 FM chipset on Japanese systems: 9 channels (or 6 + 3 drums), 15+1 instruments, hardware vibrato and amplitude modulation. ----------------------------------------------------------------------------- ----------------------------------------------------------------------------- 2. SMS Joypads Pinouts Copied from Linux Joystick Driver documentation http://atrey.karlin.mff.cuni.cz/~vojtech/joystick/ ----------------------------------------------------------------------------- Pinouts are shown looking into a controller plug. +-----------> Power (unused on most controllers) | +---------> Right | | +-------> Left | | | +-----> Down | | | | +---> Up | | | | | _____________ 5 \ o o o o o / 1 DB-9 connector \ o o x o / 9 `~~~~~~~' 6 | | | | | +----> Button 1 | +--------> Ground +----------> Button 2 DB-9 joypads (and more generally, inputs peripherals) were of common usage on Sega Master System, Megadrive (Genesis), several older consoles, Amiga and Atari computers, etc. Although the DB-9 connector is shared by many controllers, not all uses the same pinouts as the Sega Master System controller. Old joystick might also have only one button connected. ----------------------------------------------------------------------------- ----------------------------------------------------------------------------- 3. SMS Joypads (DB-9) to Parallel port adapter (type 1) Comments by Mike Gordon. ----------------------------------------------------------------------------- This adapter schematic is natively supported by the MS-DOS version of MEKA through the Allegro library. The adapter is also usable under Windows using the DirectPad Pro driver. If you do not plan to use the MS-DOS version, building the second type of adapter is recommended. ----------------------------------------------------------------------------- Note ---- This is a copy based on the schematic available on the now defunct DirectPad Pro site. A mirror is available at: http://www.arcadecontrols.com/Mirrors/www.ziplabel.com/dpadpro/ I'm not sure who is the original author of this schematic, but it is very simple and the common nature of the adapter make it somewhat public domain knowledge. D-Connector Pinouts ------------------- DB-9 SMS Joypad plug: ------------- \ 5 4 3 2 1 / \ 9 8 7 6 / --------- DB-25 Parallel connector on PC (female): ------------------------------------------ \ 13 12 11 10 9 8 7 6 5 4 3 2 1 / \ 25 24 23 22 21 20 19 18 17 16 15 14 / -------------------------------------- Legend ------ Resistor: --vvvvv-- Circuit ------- PARALLEL PORT (DB-25) SMS PAD (DB-9) DB25:1 <-----------------------------------> DB-9:1 (Up) DB25:2 <------vvvvvvvvv---+----------------> DB-9:6 (Button 1) 10K | DB25:11 <------------------+ DB25:3 <------vvvvvvvvv---+----------------> DB-9:9 (Button 2) 10K | DB25:12 <------------------+ DB25:14 <-----------------------------------> DB-9:2 (Down) DB25:16 <-----------------------------------> DB-9:3 (Left) DB25:17 <-----------------------------------> DB-9:4 (Right) DB25:18 <------------------+----------------> DB-9:8 (Ground) | DB25:19 <------------------+ * You need a 25-pin male D-plug (DB-25) for the parallel port connection (to fit the female parallel port socket), and a 9-pin male D-plug (DB-9) for the SMS joypad connection (to fit the female joypad plug). The pin numbers should be marked on the plug itself. * The type of resistor used (metal film, carbon etc.) is not important. The resistors can be soldered directly to the DB-25 connector, i.e. connect one resistor between pin 3 and pin 12, another between pin 2 and pin 11. (And a wire link, between pins 18 and 19.) The resistor value (10K) is indicated by coloured bands on the body of the resistor, as follows, from left to right: Either: Brown Black Orange (gap) Brown or Gold or: Brown Black Black Red (gap) Brown or Gold * Use shielded cable, and use the outer shield of the cable for the Ground connection. Try and keep the cable as short as possible. ----------------------------------------------------------------------------- ----------------------------------------------------------------------------- 4. SMS Joypads (DB-9) to Parallel port adapter (type 2) Comments by Gary Pierce (Youltar). ----------------------------------------------------------------------------- Please refer to SmsCartPad homepage for more detailed instruction: http://www.smspower.org/smscartpad/ ----------------------------------------------------------------------------- Circuit ------- PARALLEL PORT (DB-25) SMS PAD (DB-9) DB25:2 <-----------------------------------> DB-9:1 (Up) DB25:3 <-----------------------------------> DB-9:2 (Down) DB25:4 <-----------------------------------> DB-9:3 (Left) DB25:5 <-----------------------------------> DB-9:4 (Right) DB25:6 <-----------------------------------> DB-9:6 (Button 1) DB25:1 <-----------------------------------> DB-9:5 (Power) DB25:18 <-----------------------------------> DB-9:8 (Ground) DB25:7 <-----------------------------------> DB-9:9 (Button 2) DB25:14 <-----------------------------------> DB-9:7 (?) After some research and digging around this is the diagram I have found to work best for me. As you can see above, there is no need for any diodes or resistors. This is a straight-through connection. All one needs to do is connect the proper pins from the DB 9 to the DB 25 connector. I used an old IDE ribbon cable and some crimp on connectors. That's it. (I used crimp connectors because my soldering skills are somewhat lacking) Select the "Linux-DB9" in the driver configuration window. ----------------------------------------------------------------------------- ----------------------------------------------------------------------------- 5. SMS Joypads (DB-9) to Parallel port adapter (GNU/Linux) ----------------------------------------------------------------------------- GNU/Linux kernels starting version 2.2 supports a wide range of joysticks, based on the "Linux Joystick Driver" project: http://atrey.karlin.mff.cuni.cz/~vojtech/joystick/ Please refer to appropriate documentation (joystick-parport.txt) for detailed instruction about how to build different kind of adapters. ----------------------------------------------------------------------------- ----------------------------------------------------------------------------- 6. SMS 3-D Glasses to Serial/COM port adapter Unknown original author. Comments by Frank and Mike Gordon. ----------------------------------------------------------------------------- This adapter schematic is natively supported by the MS-DOS and Windows versions of MEKA. As of yet, UN*X versions does not support this feature. ----------------------------------------------------------------------------- Please refer to SmsCartPad homepage for more detailed instruction: http://www.smspower.org/smscartpad/3d_glasses.shtml ----------------------------------------------------------------------------- Note ---- About the MS-DOS version of MEKA: the SMS 3-D Glasses adapter should work even under in a Windows 95/98 command prompt, but I have not done extensive testing to confirm. Please e-mail me any problem you may have. Legend ------ Diode: --|>|-- Resistor: --vvvvv-- | Capacitor: --- --- | Circuit ------- RS-232 DB25 / DB9 10K RTS 4 7 Switching signal +/- 10V --------vvvvv--+ | | GND 7 5 Ground ----+-------------+--+---------+--|----+ | | | | | | | | +-|>|--+ | | | +--|>|--+ --- | | | | Transistor | --- 22 uF | | | | 2N2222 | | | | | +-+---------+ | | | | | | Emitter | | | | | | | | DTR 20 4 Vdd +10V --|>|-----+-----+ +--|--+--+ Base | | | | | +--+--+--+-+-vvvvv---+--|-----+ Collector | | | | | 10K | | | | | | | | | | +-----------+ +-------+--+--+--+-----------+--+--+ | 1 9 13 14 5 7 | | | | RCA CD 4030 Quad XOR gate | | | | 2 11 12 3 6 8 10 4 | +-+--+---+-------+--+--+----+---+--+ | | | | | | | | +--+ | +--+--+ | +--- Outside of jack | | | | | +-vvvvv-+ | +------- Middle of jack | 22K | | | | +------------ Centre of jack +-vvvvv-----+ | 22K | | --- | .01 uF --- | | | +-----+ [FRANK] This is my best attempt at a rendition of the circuit which connects my SEGA glasses to my AT. I didn't design the circuit -- I'm a software rather than hardware person. In fact I barely understand it -- as far as I can tell, the .01uF capacitor & the 22K resistors act as a delay. The outputs of the XOR gates feed back into their own inputs, thus producing an oscillator. The "jack" mentioned in the diagram is the mini-jack which is connected as standard to the glasses. "Centre", "middle", and "outside" relate to the external connections, looking at the thing end-on. Caveat emptor... to paraphrase the standard software licence agreement: It's as good as I can get it. If it doesn't work or blows up your computer or your glasses and blinds you for life, I'll give you back all the money you paid me. [MIKE GORDON] As far as I can see, the oscillator circuit is used to provide an AC supply to power the glasses. The switching signal (+ or - 10 volts) applied to the base of the transistor produces a high or low output on the collector, which presumably is used to switch between left and right frames. When building the adapter: * Use a CMOS series 4030B (or 4070B, which is functionally equivalent). Do not use a 74HC series chip. Chip pin numbering: 7 6 5 4 3 2 1 +-------------------+ | | | 4070B < - notch | | +-------------------+ 8 9 10 11 12 13 14 * Use 1N4148 (or equivalent) signal diodes. The positive end is marked by a black band around the component. Negative - --|>|-- + Positive * The resistors should ideally be metal film types (blue-coloured body). The value is indicated by coloured bands, as follows, from left to right: 22K - Red Red Orange (gap) Brown or Gold OR - Red Red Black Red (gap) Brown or Gold 10K - Brown Black Orange (gap) Brown or Gold OR - Brown Black Black Red (gap) Brown or Gold * The .01 uF (10 nF) capacitor should be a ceramic disc type, while the 22uF capacitor should be an electrolytic type. * For the 2N2222A transistor (looking at it from below, with the pins towards you) : o - Base Emitter - o o - Collector Metal tab - /_/ * The serial port is a 9-pin D-type male connector, so you need a 9-pin female D plug for the adapter. Looking into the serial port itself, this is the pin configuration: 1 2 3 4 5 ------------- \ o o o o o / \ o o o o / --------- 6 7 8 9 * Finally, the 3-D glasses jack is a 3.5mm stereo phone socket, i.e. the Walkman type. Good luck building the adapter, and enjoy! ----------------------------------------------------------------------------- ----------------------------------------------------------------------------- 7. More ? ----------------------------------------------------------------------------- If you have something interesting to contribute to this document, feel free to contact me about it (see my e-mail in the MEKA.TXT file). -----------------------------------------------------------------------------